Revista 25 - 3

Published

2005-09-01

Concepts of design for manufacturing (DFM) of lost wax parts

Conceptos de diseño para manufactura (DFM) de piezas microfundidas

DOI:

https://doi.org/10.15446/ing.investig.v25n3.14657

Keywords:

design for manufacturing, lost wax process (investment casting) (en)
diseño para manufactura, microfundición (fundición de precisión) (es)

Downloads

Authors

  • Claudia Marcela Sánchez R Universidad Nacional de Colombia
  • Carlos Julio Cortés Rodríguez Universidad Nacional de Colombia

Integrated Product Design uses several methodologies, Design for Manufacturing is one of them. DFM pretends to facilitate manufacturing of parts by means of analysis of geometries, values and tolerances, and is used in first design stages in order to decrease the product cost. The design for manufacturing was studied as well as design rules to propose a methodology for Design for Investment Casting.

Una de las metodologías utilizadas por la ingeniería concurrente o diseño integrado de productos es el diseño para manufactura, DFM. Esta técnica, que está orientada a mejorar la fabricación de piezas analizando geometrías, valores y tolerancias, es utilizada en las primeras etapas de diseño para disminuir los costos de los elementos a fabricar. Se estudió el diseño para manufactura estableciendo reglas de diseño a fin de elaborar una metodología para diseño en microfundición.

References

AK steel, 316/316L Technical Data, 2000.

ASM, ASM Metals Handbook, 10th edition, Vol. 1, “Properties and Selection Irons, Steels and High performance alloys”.

ASM, ASM Metals Handbook, 10th edition, Vol. 2, “Properties and Selection Non Ferrous Alloys”.

ASM, ASM Metals Handbook, 8th edition, Vol. 5, “Casting Article: Investment Casting”.

Bernal, J.; Martínez, F., “Estudio de materiales para la construcción por microfundición de la turbina de un turbocargador”, proyecto de grado presentado a la Universidad Nacional de Colombia para optar al título de ingeniero mecánico, 1996.

Boothroyd, G.; Dewhrst, P; Knight, W., Product Design for Manufacture and Assembly, second edition, Marcel Dekker.

Bralla, J., Handbook of Product Design for Manufacturing. A practical guide to low cost production”, McGraw-Hill, 1993.

Cast Metals Institute, Inc., 10 Rules for Cost Effective Casting Design, Metal Casting Design, 2002.

Chalmers, Bruce, Metalurgia física, Aguilar Ediciones, Madrid, 1968.

Colton, J.S., Manufacturing Processes and Engineering, Georgia Institute of Technology Special Publication,2003.

Crow, Kenneth., Design for Manufacturing, DRM Associates, 2001.

Ebrahimi, S. A.; Tortorelli, D. A. y Dantzig J. A., Sensitivity analysis and nonlinear programming applied to investment Casting design, Math Modeling Vol 21,1998. DOI: https://doi.org/10.1016/S0307-904X(96)00155-2

Encyclopedic Handbook of Biomaterials and Bioengineering, Part B, “Applications”, Vol. I, Marcel Dekker, Inc. 1995.

Etebari, A.; Ferrante, J. y Wojcik, L., Advanced Lateral Mobility Prosthetic Ankle Design, Virginia Tech Spring Semester, 1998.

Gdaumann, M. y Sholapurwalla, A, “Investment Casting Simulation”, Calcom SA (Lausanne, Switzerland, www.calcom.ch), UES Software Inc. (Annapolis MD USA, www.ues-sottware.com), 2002.

Gebelin, J. C.; Jolly, M. R., “Modelling of the investment casting process”, Journal of Materials Processing Technology, Vol.135 pp. 291-300, 2003. DOI: https://doi.org/10.1016/S0924-0136(02)00860-9

Hallab, N.; Mikecz, K.; Akrami, J.; Jacobs, J., “Titanium and Chromium Release into and Binding with Human Serum from: Titanium and Cobaltchromium Implant Alloy Degradation”, 46th Annual Meeting Orthopaedic Research Society, Orlando, Florida, March, 2000.

Hamilton, R.W.; See D.; Butler S.; Lee, PD., “Multiscale modeling for the prediction of casting defects in investment cast aluminum alloys”, Materials Science and Engineering, Section A, 2003. DOI: https://doi.org/10.1016/S0921-5093(02)00376-3

Hermanek, F; Spike, R, Finding the lost wax process, Vol. 32, No.1, 2002.

Hitchiner Manufacturing Co., Inc., Designing for investment casting, Technical Updated 2D1, 2000.

Hitchiner Manufacturing Co., Inc., An Introduction to the Investment Casting Process, Technical Updated, 2000.

Hover, A, “Titanio para fijación de fracturas”, O&T nuevos Avances en ortopedia y traumatología, Año 3, No. 6, abril, 1998.

Hsu, W.; Liu, B., Conceptual design: issues and challenges, National University of Singapore, Computer-Aided Design, 2000. DOI: https://doi.org/10.1016/S0010-4485(00)00074-9

http://cdr.standford.edu/html/DD/PEARL/home.html

http://www.ccbda.org/publications/pub13e/Investment_Casting.html

http://www.dfma.com/

http://www.etunda.com/processes/metal_processing/Investmet_Casting.cfm

http://www.hitchiner.com/home.html

http://www.hitchiner.com/home.html

http://www.kp.dir.de/WB-RS/Erstarrung/web_eng/herstell_eng.html

http://www.me.iastate.edu/me324_bahadur/Section%202.2/2_1.htm

http://www.munroassoc.com/index.htm

http://www.northernprecision.com/facts.htm

http://www.npd-solutions.com/designguidelines.html

http://www.rugergolf.com/titanium.htm

http://www.stsa.org/stsa/dsgmilcr.html

http://www.sintet.no/units/matek/projects/dtm.htm

http://www.tms.org/pubs/journals/JOM/jom.html

IDA (Institute for Defense Analysis), report R-338, 1986.

Jolly, M.; Cox, M.; Gebelin, J.; Jones, S.; y Cendrowicz A, “Modelling the Investment Casting Process, Fundamentals of Investment Casting (FOCAST) IRC in Materials”, University of Birmingham, UK American Foundry Society, 2001.

Jones, S.; Yuan, C., “Advances in shell moulding for investment casting”, Journal of Materials Processing Technology, Vol 135 pp. 258-265, 2003. DOI: https://doi.org/10.1016/S0924-0136(02)00907-X

Lackritz, H.; Chernomorsky, A.; Fariabi, S.; Selvaduray G., “Biomaterials in Medical Devices”, Mate 175, 2002.

Long, M.; Rack, H.J., “Titanium alloys in total joint replacement—a materials science perspective”, Biomaterials Elsevier, 1998. DOI: https://doi.org/10.1016/S0142-9612(97)00146-4

McCloskey, J.C., “Productivity in Investment Casting”, American Jewelry Manufacturing, Vol. 38, No. 6, June, 1990, p. 32.

Memorias “Segundo seminario de fundición de precisión a la cera perdida”, Grupo de Cera Perdida, Medellín, Universidad de Antioquia, noviembre, 1992.

Nanua, S., Systems approach to Computer integrated design and manufacturing, John Wiley & Sons, 1996.

O'Driscoll, M., “Design for Manufacturing”, Journal of Materials Processing Technology, Vol 122 pp. 318-321, 2002. DOI: https://doi.org/10.1016/S0924-0136(01)01132-3

Ohkubo, C.; Watanabe, I.; Ford, J.P; Nakajima, H.; Hosoi, T.; Okabe, T., “The machinability of cast titanium and Ti6Al4V”, Biomaterials, 2000.

Ohkubo C.; Watanabe I.; Ford J.P; Nakajima, H., Hosoi, T.; Okabe T., “The machinability of cast titanium and Ti6Al4V”, Biomaterials 2000. DOI: https://doi.org/10.1016/S0142-9612(99)00206-9

O'Mahoney, D.; Browne, D.J., “Use of experiment and an inverse method to study interface heat transfer during solidification in the investment casting process”, Experimental Thermal and Fluid Science, Vol 22 pp. 111 - 122, 2000. DOI: https://doi.org/10.1016/S0894-1777(00)00014-5

Orlov, “Ingeniería del diseño”, Cap. 3, Diseño de piezas de fundición, Ed. Mir.

Ouellette, J., Biomaterials Facilitate Medical Breakthroughs, American Institute of Physics, 2001.

Ozols, A., “Aleaciones Implantables”, Facultad de Ingeniería, UBA, En http://www.odontologia-online.com/casos/tecnologia/TN2/tn2.html

Pérez, A. J., “Estudio de materiales bioimplantables y factibilidad de producción en el País”, proyecto de grado presentado a la Universidad Nacional de Colombia, para optar al título de ingeniero mecánico, 1986.

Piehler, H. R., “The Future of Medicine: Biomaterials”, mrs bulletin, august, 2000.

Prasad, K.D.V.; Yarlagadda, SiangHock, T., “Statistical Analysis on Accuracy of Wax Patterns Used in Investment Casting Process”, Journal of Material Processing and Technology,Vol 138 pp. 75-81, 2003. DOI: https://doi.org/10.1016/S0924-0136(03)00052-9

Ravi, B., Casting Design and Analysis, Lecture Notes, II T, Bombai, 2002.

Reed, S., “Investment Casting of Titanium Using the Induction Skull Melting Process”, Flowserve Corporation, Jai Narayan — Consarc Corporation.

Röhrig, K., “Castings from stainless steels and nickel-base alloys”, Consultant to the Nickel Development Institute.

Rosero, M.V., “Estudio de los biomateriales para el desarrollo de endoprótesis”, proyecto de grado presentado a la Universidad Nacional de Colombia, para optar al título de ingeniero mecánico, 2003.

Sánchez, J.; Priest, J.; Soto, R., “An Intelligent Reasoning Assistant for Incorporating Manufacturability issues into the Design Process”, Expert Systems with Applications, Vol. 12 No. 1, 1997. DOI: https://doi.org/10.1016/S0957-4174(96)00082-6

Sánchez, C., “Conceptos de diseño para manufactura DFM de piezas microfundidas para aplicación en dispositivos biomecánicos”, proyecto de grado presentado a la Universidad Nacional de Colombia, para optar al título de ingeniera mecánica, 2003.

Shina, S. G., “Faster New Product Development Through DFM and Concurrent Engineering”, NEPCON’99. en Suntio, Teuvo Electronic Product Design, Power Electronics, University of Oulu 2001.

Simmons, J. M, “Designing for investment casting, Machine design”, Vol 72 No.17 pp.92, 2000.

Starbek, M; Grum, J., “Concurrent engineering in small companies”, international Journal of Machine Tools & Manufacture, Vol 42 pp 417-426, 2002. DOI: https://doi.org/10.1016/S0890-6955(01)00111-0

Su X., “Computer Aided Optimization of an Investment Bi-Metal Casting Process”, University of Cincinnati, 2001.

The century in Orthopedics, en: Orthopedics Today, January, 2000.

The Legacy of Investment Casting, Hitchiner Manufacturing Co., Inc, April, 1998.

Thomas, B.G., Metals processing, Chapter 14: Structure, processing and properties of engineering Materials, Ed. Adison Wesley

Tien-Chien, C.; Wysk, R.A. y Hsu-Pin, W., Computer-Aided Manufacturing, second edition, pp. 596-598, Prentice- Hall, 1998.

Tolerancias generales, Hitchiner Manufacturing Co., Inc.

Tu, J.; S., Foran, R.; K.; Hines, A. M. y Aimone, PR., “An Integrated Procedure for Modeling Investment Castings”, JOM (Minerals Metals and Materials Society publication).

Ulrich, K.; Eppoinger, S., Product Design and Development, McGraw-Hill, 1995.

Vandamme, N. S.; Que, L.; Topoleski, L.; D. T., “Carbide surface coating of Co-Cr-Mo implant alloys by a microwave plasma-assisted reaction”, en: Journal of Materials Science, Vol 34 pp. 3525-3531, 1999. DOI: https://doi.org/10.1023/A:1004670207579

Vernon, C., “Design for Manufacturing”, OISM, 2001.

Winsconsin precision, Investment Casting Design Parameters, Technical information provided with permission from The Investment Casting Institute.

Yankee, H., Manufacturing Processes, Ed. Prentice-Hall, 1979.

Yao, W.L.; Leu, M.C., “Analysis and design of internal web structure of laser stereolithography patterns for investment casting”, Materials and Design, Vol,21 pp.101 -109, 2000. DOI: https://doi.org/10.1016/S0261-3069(99)00061-8

Yoneda, T.; Sato, T.; Niyama, E., “Apparent Solidification Shrinkage of Titanium Castings Induction-Melted in Lime Crucible”, YAC Vol 67 pp.749, 1995.

Yu, J.C.; Krizan, S.; Ishii, K., “Computer Aided Design for Manufacturing Process Selection”, Ohio State University, en Journal of Intelligent Manufacturing, 1992.

Yu, Jyh-Cheng.; Krizan, S.; Ishii, K., “Computer Aided Design for Manufacturing Process Selection”, Ohio State University, en: Journal of Intelligent Manufacturing, 1992.

How to Cite

APA

Sánchez R, C. M. and Cortés Rodríguez, C. J. (2005). Concepts of design for manufacturing (DFM) of lost wax parts. Ingeniería e Investigación, 25(3), 49–60. https://doi.org/10.15446/ing.investig.v25n3.14657

ACM

[1]
Sánchez R, C.M. and Cortés Rodríguez, C.J. 2005. Concepts of design for manufacturing (DFM) of lost wax parts. Ingeniería e Investigación. 25, 3 (Sep. 2005), 49–60. DOI:https://doi.org/10.15446/ing.investig.v25n3.14657.

ACS

(1)
Sánchez R, C. M.; Cortés Rodríguez, C. J. Concepts of design for manufacturing (DFM) of lost wax parts. Ing. Inv. 2005, 25, 49-60.

ABNT

SÁNCHEZ R, C. M.; CORTÉS RODRÍGUEZ, C. J. Concepts of design for manufacturing (DFM) of lost wax parts. Ingeniería e Investigación, [S. l.], v. 25, n. 3, p. 49–60, 2005. DOI: 10.15446/ing.investig.v25n3.14657. Disponível em: https://revistas.unal.edu.co/index.php/ingeinv/article/view/14657. Acesso em: 24 apr. 2024.

Chicago

Sánchez R, Claudia Marcela, and Carlos Julio Cortés Rodríguez. 2005. “Concepts of design for manufacturing (DFM) of lost wax parts”. Ingeniería E Investigación 25 (3):49-60. https://doi.org/10.15446/ing.investig.v25n3.14657.

Harvard

Sánchez R, C. M. and Cortés Rodríguez, C. J. (2005) “Concepts of design for manufacturing (DFM) of lost wax parts”, Ingeniería e Investigación, 25(3), pp. 49–60. doi: 10.15446/ing.investig.v25n3.14657.

IEEE

[1]
C. M. Sánchez R and C. J. Cortés Rodríguez, “Concepts of design for manufacturing (DFM) of lost wax parts”, Ing. Inv., vol. 25, no. 3, pp. 49–60, Sep. 2005.

MLA

Sánchez R, C. M., and C. J. Cortés Rodríguez. “Concepts of design for manufacturing (DFM) of lost wax parts”. Ingeniería e Investigación, vol. 25, no. 3, Sept. 2005, pp. 49-60, doi:10.15446/ing.investig.v25n3.14657.

Turabian

Sánchez R, Claudia Marcela, and Carlos Julio Cortés Rodríguez. “Concepts of design for manufacturing (DFM) of lost wax parts”. Ingeniería e Investigación 25, no. 3 (September 1, 2005): 49–60. Accessed April 24, 2024. https://revistas.unal.edu.co/index.php/ingeinv/article/view/14657.

Vancouver

1.
Sánchez R CM, Cortés Rodríguez CJ. Concepts of design for manufacturing (DFM) of lost wax parts. Ing. Inv. [Internet]. 2005 Sep. 1 [cited 2024 Apr. 24];25(3):49-60. Available from: https://revistas.unal.edu.co/index.php/ingeinv/article/view/14657

Download Citation

CrossRef Cited-by

CrossRef citations2

1. Pedro Agustín Ojeda-Escoto. (2021). Redesigning a product: Assembly, manufacture and production strategies. Revista de Operaciones Tecnologicas, , p.1. https://doi.org/10.35429/JTO.2021.15.5.1.9.

2. Susana Paixão-Barradas, Bernabé Hernandis Ortuño, Begoña Agudo Vicente, Isadora Dickie, Karla Mazarelo Maciel Pacheco. (2012). Design in the natural stone transformation sector: evaluating a new concept. Ingeniería e Investigación, 32(3), p.83. https://doi.org/10.15446/ing.investig.v32n3.35948.

Dimensions

PlumX

Article abstract page views

619

Downloads

Download data is not yet available.
Crossref
Scopus
Google Scholar
Europe PMC

License

Copyright (c) 2005 Carlos Julio Cortés Rodríguez, Claudia Marcela Sánchez R

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The authors or holders of the copyright for each article hereby confer exclusive, limited and free authorization on the Universidad Nacional de Colombia's journal Ingeniería e Investigación concerning the aforementioned article which, once it has been evaluated and approved, will be submitted for publication, in line with the following items:

1.    The version which has been corrected according to the evaluators' suggestions will be remitted and it will be made clear whether the aforementioned article is an unedited document regarding which the rights to be authorized are held and total responsibility will be assumed by the authors for the content of the work being submitted to Ingeniería e Investigación, the Universidad Nacional de Colombia and third-parties;

2.    The authorization conferred on the journal will come into force from the date on which it is included in the respective volume and issue of Ingeniería e Investigación in the Open Journal Systems and on the journal's main page (https://revistas.unal.edu.co/index.php/ingeinv), as well as in different databases and indices in which the publication is indexed;

3.    The authors authorize the Universidad Nacional de Colombia's journal Ingeniería e Investigación to publish the document in whatever required format (printed, digital, electronic or whatsoever known or yet to be discovered form) and authorize Ingeniería e Investigación to include the work in any indices and/or search engines deemed necessary for promoting its diffusion;

4.    The authors accept that such authorization is given free of charge and they, therefore, waive any right to receive remuneration from the publication, distribution, public communication and any use whatsoever referred to in the terms of this authorization.