Correo Electrónico
DNINFOA - SIA
Bibliotecas
Convocatorias
Identidad U.N.
Publicado
Effect of FC3R on the properties of ultra-high-performance concrete with recycled glass
Efecto del FC3R en las propiedades del concreto de ultra altas prestaciones con vidrio reciclado
DOI:
https://doi.org/10.15446/dyna.v86n211.79596Palabras clave:
ultra-high performance concrete, sustainable construction materials, waste management (en)concreto de ultra altas prestaciones, construcción sostenible, gestión de residuos (es)
Descargas
Ultra-high-performance concrete (UHPC) is the essential innovation in concrete research of the recent decades. However, because of the high contents of cement and silica fume used, the cost and environmental impact of UHPC is considerably higher than conventional concrete. The use of industrial byproducts as supplementary cementitious materials, in the case of recycled glass powder and fluid catalytic cracking catalyst residue (FCC), the partial substitution of cement and silica fume allows to create a more ecological and cost-efficient UHPC. This research presents a study to determine the possibility of partial substitution of cement by FCC in a previously optimized mixture of ultra-high-performance concrete with recycled glass. The results demonstrate that compressive strength values of 150 and 151 MPa without any heat treatment can be achieved, respectively, when replacing 11% and 15% of the cement with FCC, for a determined amount of water and superplasticizer, compared to 158 MPa obtained for the reference UHPC without any FCC content. The rheology of fresh UHPC is highly decreased by replacing cement particles with FCC.
El concreto de ultra altas prestaciones (UHPC) supone el máximo exponente en la investigación sobre concretos especiales en las últimas décadas. Sin embargo, debido a su elevado contenido en cemento y humo de sílice, el costo e impacto ambiental del UHPC es considerablemente superior al del concreto convencional. El empleo de co-productos industriales como materiales cementantes suplementarios, caso del polvo de vidrio reciclado y el residuo de craqueo catalítico, en sustitución parcial del cemento y del humo de sílice permite crear un UHPC más respetuoso con el medioambiente y más eficiente en costo. Esta investigación presenta un estudio para determinar la posibilidad de sustitución parcial de cemento por FCC en una mezcla previamente optimizada de UHPC que incorpora polvo de vidrio en su composición. Los resultados muestran que es posible alcanzar una resistencia de 150 y 151 MPa sin ningún tratamiento térmico al reemplazar un 11% y 15% del peso de cemento por FCC respectivamente para una cantidad de agua y superplastificante determinadas, en comparación con los 158 MPa obtenidos para la muestra de referencia sin FCC. La reología del UHPC se ve fuertemente afectada cuando se sustituye cemento por FCC.
Referencias
Abellan, J., Torres, N., Núñez, A. y Fernández, J., Influencia del exponente de Fuller, la relación agua conglomerante y el contenido en policarboxilato en concretos de muy altas prestaciones, en: IV Congreso Internacional de Ingenieria Civil, 2018.
Soliman, N.A. and Tagnit-Hamou, A., Using particle packing and statistical approach to optimize eco-efficient ultra-high-performance concrete, ACI Mater. J., 114(6), pp. 847-858, 2017. DOI: 10.14359/51701001.
Ghafari, E., Costa, H., Nuno, E. and Santos, B., RSM-based model to predict the performance of self-compacting UHPC reinforced with hybrid steel micro-fibers, Constr. Build. Mater., 66(September), pp. 375-383, 2014. DOI: 10.1016/j.conbuildmat.2014.05.064
Schmidt, C. and Schmidt, M., Whitetopping of asphalt and concrete pavements with thin layers of ultra-high-performance concrete - Construction and economic efficiency, in: 3rd International Symposium on UHPC and Nanotechnology for High Performance Construction Materials, no. 19, M.S.E.F.C.G.S. Fröhlich and S. Piotrowski, Eds. Kassel University, Kassel, Germany: 2012, pp. 921-927.
Abbas, S., Nehdi, M.L. and Saleem, M.A., Ultra-High performance concrete: mechanical performance, durability, sustainability and implementation challenges, Int. J. Concr. Struct. Mater., 10(3), pp. 271-295, 2016.
Nehdi, M., Abbas, S. and Soliman, A., Exploratory study of ultra-high performance fiber reinforced concrete tunnel lining segments with varying steel fiber lengths and dosages, Eng. Struct., 101(March), pp. 733-742, 2015. DOI: 10.1016/j.engstruct.2015.07.012
Toledo-Filho, R.D., Koenders, E.A., Formagini, S. and Fairbairn, E.M., Performance assessment of ultra high performance fiber reinforced cementitious composites in view of sustainability performance assessment of ultra high performance fiber reinforced, Mater. Des., 36, pp. 880-888, 2012. DOI: 10.1016/j.matdes.2011.09.022
Abellan, J., Torres, N., Núñez, A. and Fernández, J., Ultra high preformance fiber reinforced concrete: state of the art, applications and possibilities into the Latin American market, in: XXXVIII Jornadas Sudamericanas de Ingeniería Estructural, 2018.
Tayeh, B.A., Abu-Bakar, B.H., Megat-Johari, M.A. and Voo, Y.L., Utilization of Ultra-High Performance Fibre Concrete (UHPFC) for rehabilitation - A review, Procedia Eng., 54(December) 2013, pp. 525-538, 2013.
Soliman, N.A. and Tagnit-Hamou, A., Using glass sand as an alternative for quartz sand in UHPC, Constr. Build. Mater., 145, pp. 243-252, 2017. DOI: 10.1016/j.conbuildmat.2017.03.187
Kalny, M., Kvasnicka, V. and Komanec, J., First practical applications of UHPC in the Czech Republic, in: Proceedings of Hipermat 2016 - 4th International Symposium on UHPC and Nanotechnology for Construction Materials, 2016, pp. 147-148.
Tagnit-Hamou, A., Soliman, N.A. and Omran, A., Green Ultra-High-Performance glass concrete, First International Interactive Symposium on UHPC, 3(1), pp. 1-10, 2016. DOI: 10.21838/uhpc.2016.35
Richard, P. and Cheyrezy, M., Composition of reactive powder concretes Cem. Concr. Res., 25(7), pp. 1501-1511, 1995.
De Larrard, F. and Sedran, T., Mixture-proportioning of high-performance concrete, Cem. Concr. Res., 32(11), pp. 1699-1704, 2002.
Kou, S.C. and Xing, F., The effect of recycled glass powder and reject fly ash on the mechanical properties of fibre-reinforced Ultrahigh Performance Concrete, Hindawi Publ. Corp. Adv. Mater. Sci. Eng.,(May), 2012. DOI: 10.1155/2012/263243
Abdulkareem, O.M., Ben-Fraj, A., Bouasker, M. and Khelidj, A., Effect of chemical and thermal activation on the microstructural and mechanical properties of more sustainable UHPC, Constr. Build. Mater., 169, pp. 567-577, 2018.
Ghafari, E., Costa, H. and Júlio, E., Statistical mixture design approach for eco- efficient UHPC, Cem. Concr. Compos., 55(September), pp. 17-25, 2015. DOI: 10.1016/j.cemconcomp.2014.07.016
Meng, W., Samaranayake, V.A. and Khayat, K.H., Factorial design and optimization of UHPC with lightweight sand, ACI Mater. J., (February), 2018. DOI: 10.14359/51700995
Camacho-Torregosa, E., Dosage optimization and bolted connections for UHPFRC ties, Thesis Dr., Polytechnic University of Valencia, Spain, 2013.
Ahmad, S., Hakeem, I. and Maslehuddin, M., Development of UHPC mixtures utilizing natural and industrial waste materials as partial replacements of silica fume and sand, The Scientific World Journal, vol. 2014, pp. 1-8, 2014. DOI: 10.1155/2014/713531
Vaitkevicius, V., Šerelis, E. and Hilbig, H., The effect of glass powder on the microstructure of ultra high performance concrete, 68, pp. 102-109, 2014. DOI: 10.1016/j.conbuildmat.2014.05.101
Li, W., Huang, Z., Zu, T., Shi, C., Duan, W.H. and Shah, S.P., Influence of nanolimestone on the hydration, mechanical strength, and autogenous shrinkage of ultrahigh-performance concrete, J. Mater. Civ. Eng., 28(1), pp. 1-9, 2016. DOI: 10.1061/(ASCE)MT.1943-5533.0001327
Huang, Z. and Cao, F., Effects of nano-materials on the performance of UHPC, 材料导报B：研究篇, 26(9), pp. 136-141, 2012.
Šerelis, E., Vaitkevičius, V. and Kerševičius, V., Mechanical properties and microstructural investigation of Ultra-High Performance Glass Powder Concrete. Journal of Sustainable Architecture and Civil Engineering, 14(1), pp. 5-11, 2016. DOI: 10.5755/j01.sace.14.1.14478
Soliman, N.A. and Tagnit-Hamou, A., Partial substitution of silica fume with fine glass powder in UHPC: filling the micro gap. Constr. Build. Mater., 139, pp. 374-383, 2017. DOI: https://doi.org/10.1016/j.conbuildmat.2017.02.084
Arizzi, A. and Cultrone, G., Comparing the pozzolanic activity of aerial lime mortars made with metakaolin and fluid catalytic cracking catalyst residue : a petrographic and physical-mechanical study, Constr. Build. Mater., 184, pp. 382-390, 2018. DOI: 10.1016/j.conbuildmat.2018.07.002
Cosa, J., Soriano, L., Borrachero, M.V., Reig, L., Payá, J. and Monzó, J.M., Influence of addition of Fluid Catalytic Cracking residue (FCC) and the SiO2 concentration in alkali-activated Ceramic Sanitary-Ware (CSW) Binders. Minerals, 8(4), pp. 1-18, 2018. DOI: 10.3390/min8040123
Torres-Castellanos, N., Izquierdo-Garcia, S., Torres-Agredo, J. and Mejia-de Gutierrez, R., Resistance of blended concrete containing an industrial petrochemical residue to chloride ion penetration and carbonation, Ingeniería e Investigación, 34(1), pp. 11-16, 2014. DOI: 10.15446/ing.investig.v34n1.38730
Torres-Castellanos, N. and Torres-Agredo, J., Uso del catalizador gastado de craqueo catalítico (FCC) como adición puzolánica - revisión, Ingeniería e Investigación, 30(2), pp. 35-42, 2010.
Torres-Castellanos, N., Estudio en estado fresco y endurecido de concretos adicionados con catalizador de craqueo catalítico usado (FCC). Tesis Dr., Facultad de Ingeniería, Universidad Nacional de Colombia, Bogotá, Colombia, 2014.
Eriksson, L., Johansson, E., Kettaneh-Wold, N., WikstrÄom, C. and Wold, S., Design of experiments: principles and applications. UMEA University, Sweden, 2000.
Upasani, R.S. and Banga, A.K., Response surface methodology to investigate the iontophoretic delivery of tacrine hydrochloride, Pharm. Res., 21(12), pp. 2293-2299, 2004.
Lenth, R.V., Response-surface methods in R, using RSM. J. Stat. Softw., 32(7), pp. 1-17, 2012.
Montgomery, D.C., Design and analysis of experiments. John Wiley & Sons, Inc, New Jersey, USA, 2005.
Mosaberpanah, M.A. and Eren, O., Statistical models for mechanical properties of UHPC using response surface methodology, Comput. Concr., 19(6), pp. 667-675, 2017.
Mosaberpanah, M.A. and Eren, O., Effect of quartz powder, quartz sand and water curing regimes on mechanical properties of UHPC using response surface modeling. Adv. Concr. Constr., 5(5), pp. 481-492, 2017. DOI: 10.12989/acc.2017.5.5.481
Shaaban, M. and Ahmed, S., Development of Ultra-High Performance concrete jointed precast decks and concrete piles in integral abutment bridges, in: The First International Symposium on Jointless & Sustainable Bridges, May, 2016.
Shaaban, M. and Ahmed, S., Mechanical behaviour of Ultra-High Performance concrete obtained with different concrete constituents and mix designs, in: Resilient Infrastructure, June, 2016, pp. 702-1, 702-10.
Viet-Thein-An, V. and Ludwig, H.M., Proportioning optimization of UHPC containing rice husk ash and ground granulated blast-furnace slag, in: Proceedings of Hipermat 2012 - 3rd International Symposium on UHPC and Nanotechnology for Construction Materials, Schmidt, M., Fehling, E., Glotzbach, C., Fröhlich, S. and Piotrowski, S., Eds., Kassel University, Kassel, Germany, 2012, pp. 197-205.
R Core Team, R: a language and environment for statistical computing. Vienna, Austria, [online]. 2018. Available at: https://www.R-project.org/.
Funk, J.E. and Dinger, D., Predictive process control of crowded particulate suspensions: applied to ceramic manufacturing. 1994.
ASTM and ASTM C1437, ‘Standard test method for flow of hydraulic cement mortar,’ American Society for Testing and Materials C-1437, no. C1437. ASTM, Conshohocken, PA, pp. 1-2, 2016.
ASTM, Standard test method for compressive strength of hydraulic cement mortars (Using 2-in . or [50-mm] Cube Specimens), American Society for Testing and Materials C-109/C109M, no. C109/C109M - 11b. ASTM, pp. 1-9, 2010.
The European Project Group, ‘The european guidelines for self-compacting concrete,’ The European Guidelines for Self Compacting Concrete, no. May. EFNARC, 2005, 63 P.
Gómez, E. and Zornoza, M., El papel del catalizador usado de Craqueo Catalítico (FCC) como material puzolánico en el proceso de corrosión de armaduras de hormigón., Valencia, España, 2007.
Puertas, F., Santos, H., Palacios, M. and Martínez-Ramírez, S., Polycarboxylate superplasticiser admixtures: effect on hydration, microstructure and rheological behaviour in cement pastes. Adv. Cem. Res., 17(2), pp. 77-89, 2005.
Kubens, S., Interaction of cement and admixtures and its influence on rheological properties. Thesis, Universität Weimar, Göttingen, Germany, 2010, 192 P.
Cómo citar
IEEE
ACM
ACS
APA
ABNT
Chicago
Harvard
MLA
Turabian
Vancouver
Descargar cita
CrossRef Cited-by
1. Amin Abrishambaf, Mário Pimentel, Sandra Nunes, Carla Costa. (2022). Multi-level study on UHPFRC incorporating ECat. Construction and Building Materials, 318, p.125976. https://doi.org/10.1016/j.conbuildmat.2021.125976.
2. Joaquín Abellán-García, Juan J. Ortega-Guzmán, Diego A. Chaparro-Ruiz, Eliana García-Castaño. (2022). A Comparative Study of LASSO and ANN Regressions for the Prediction of the Direct Tensile Behavior of UHPFRC. Advances in Civil Engineering Materials, 11(1), p.235. https://doi.org/10.1520/ACEM20210101.
3. Joaquín Abellán-García, Andrés M. Núñez-López, Samuel E. Arango-Campo. (2021). Fibre Reinforced Concrete: Improvements and Innovations. RILEM Bookseries. 30, p.864. https://doi.org/10.1007/978-3-030-58482-5_76.
4. N. Marcela Redondo-Pérez, Jesús D. Redondo-Mosquera, Joaquín Abellán-García. (2024). A Comprehensive Overview of Recycled Glass as Mineral Admixture for Circular UHPC Solutions. Sustainability, 16(12), p.5077. https://doi.org/10.3390/su16125077.
5. Joaquín Abellán-García, María Alejandra Santofimio-Vargas, Nancy Torres-Castellanos. (2020). Analysis of Metakaolin as Partial Substitution of Ordinary Portland Cement in Reactive Powder Concrete. Advances in Civil Engineering Materials, 9(1), p.368. https://doi.org/10.1520/ACEM20190224.
6. Joaquín Abellán-García. (2024). Effect of rice husk ash as partial replacement of ordinary Portland cement in ultra-high-performance glass concrete. European Journal of Environmental and Civil Engineering, 28(3), p.661. https://doi.org/10.1080/19648189.2023.2219722.
7. Joaquin Abellan-Garcia, Yassir M. Abbas, Mohammad Iqbal Khan, Francisco Pellicer-Martínez. (2024). ANOVA-guided assessment of waste glass and limestone powder influence on ultra-high-performance concrete properties. Case Studies in Construction Materials, 20, p.e03231. https://doi.org/10.1016/j.cscm.2024.e03231.
8. Jamshid Esmaeili, Ammar Oudah AL-Mwanes. (2021). Performance Evaluation of Eco-Friendly Ultra-High-Performance Concrete Incorporated with Waste Glass-A Review. IOP Conference Series: Materials Science and Engineering, 1094(1), p.012030. https://doi.org/10.1088/1757-899X/1094/1/012030.
9. Joaquín Abellán-García. (2023). Numerical Modeling Strategies for Sustainable Concrete Structures. RILEM Bookseries. 38, p.1. https://doi.org/10.1007/978-3-031-07746-3_1.
10. Jesús D. Redondo-Mosquera, David Sánchez-Angarita, Marcela Redondo-Pérez, Juan C. Gómez-Espitia, Joaquín Abellán-García. (2023). Development of high-volume recycled glass ultra-high-performance concrete with high C3A cement. Case Studies in Construction Materials, 18, p.e01906. https://doi.org/10.1016/j.cscm.2023.e01906.
11. Joaquín Abellán-García, Jairo A. DSánchez-Díaz, Victoria Eugenia Ospina-Becerra. (2022). Neural network-based optimization of fibres for seismic retrofitting applications of UHPFRC. European Journal of Environmental and Civil Engineering, 26(13), p.6305. https://doi.org/10.1080/19648189.2021.1938687.
12. Joaquín Abellán-García. (2022). Study of nonlinear relationships between dosage mixture design and the compressive strength of UHPC. Case Studies in Construction Materials, 17, p.e01228. https://doi.org/10.1016/j.cscm.2022.e01228.
13. Ngoc-Hien Nguyen, Joaquín Abellán-García, Seunghye Lee, Trung-Kien Nguyen, Thuc P. Vo. (2023). Simultaneous prediction the strain and energy absorption capacity of ultra-high performance fiber reinforced concretes by using multi-output regression model. Construction and Building Materials, 384, p.131418. https://doi.org/10.1016/j.conbuildmat.2023.131418.
14. Jamshid Esmaeili, Ammar Oudah AL-Mwanes. (2021). A review: Properties of eco-friendly ultra-high-performance concrete incorporated with waste glass as a partial replacement for cement. Materials Today: Proceedings, 42, p.1958. https://doi.org/10.1016/j.matpr.2020.12.242.
15. Yunfeng Qian, Muhammad Sufian, Oussama Accouche, Marc Azab, Ahmed Mohammed. (2022). Advanced machine learning algorithms to evaluate the effects of the raw ingredients on flowability and compressive strength of ultra-high-performance concrete. PLOS ONE, 17(12), p.e0278161. https://doi.org/10.1371/journal.pone.0278161.
16. Metin Katlav, Faruk Ergen. (2025). Improved forecasting of the compressive strength of ultra‐high‐performance concrete (UHPC) via the CatBoost model optimized with different algorithms. Structural Concrete, 26(1), p.212. https://doi.org/10.1002/suco.202400163.
17. Joaquín Abellán-García, Jaime A. Fernández-Gómez, Nancy Torres-Castellanos, Andrés M. Núñez-López. (2021). Fibre Reinforced Concrete: Improvements and Innovations. RILEM Bookseries. 30, p.570. https://doi.org/10.1007/978-3-030-58482-5_52.
18. Ting Wang, Zhanbing He. (2024). Compressive strength evaluation of ultra-great workability concrete by creating hybridized regression analysis. International Journal for Computational Methods in Engineering Science and Mechanics, 25(3), p.165. https://doi.org/10.1080/15502287.2023.2294289.
19. Chander Mohan Kansal, Rajesh Goyal. (2021). Analysing mechanical properties of concrete with nano silica, silica fume and steel slag. Materials Today: Proceedings, 45, p.4520. https://doi.org/10.1016/j.matpr.2020.12.1032.
20. Nemesio Daza, Yoleimy Ávila, Andrés Guzmán, Joaquín Abellán-Garcia. (2023). Testing and Experimentation in Civil Engineering. RILEM Bookseries. 41, p.231. https://doi.org/10.1007/978-3-031-29191-3_20.
21. Mohammad Iqbal Khan, Yassir M. Abbas, Galal Fares, Fahad K. Alqahtani. (2023). Strength prediction and optimization for ultrahigh-performance concrete with low-carbon cementitious materials – XG boost model and experimental validation. Construction and Building Materials, 387, p.131606. https://doi.org/10.1016/j.conbuildmat.2023.131606.
22. Yassir M. Abbas, M. Iqbal Khan, Joaquin Abellan-Garcia, Andrea Castro-Cabeza. (2024). Synergizing metakaolin and waste-glass for sustainable and functional UHPCC– a central composite design and ecological footprint assessment. Journal of Building Engineering, 95, p.110249. https://doi.org/10.1016/j.jobe.2024.110249.
23. Ngoc-Hien Nguyen, Joaquín Abellán-García, Seunghye Lee, Eliana Garcia-Castano, Thuc P. Vo. (2022). Efficient estimating compressive strength of ultra-high performance concrete using XGBoost model. Journal of Building Engineering, 52, p.104302. https://doi.org/10.1016/j.jobe.2022.104302.
24. Pedro Lucas Cruz, Lucas Veiga Ávila, Maria Alzira Pimenta Dinis, Daniel Knebel Baggio. (2023). Environmental, social and governance (ESG) and innovation in the construction sector: Systematic Literature Review. Revista de Administração da UFSM, 16(4) https://doi.org/10.5902/1983465975315.
25. Joaquín Abellán-García. (2020). Four-layer perceptron approach for strength prediction of UHPC. Construction and Building Materials, 256, p.119465. https://doi.org/10.1016/j.conbuildmat.2020.119465.
26. Joaquín Abellán-García, Juan Sebastián Guzmán-Guzmán. (2021). Random forest-based optimization of UHPFRC under ductility requirements for seismic retrofitting applications. Construction and Building Materials, 285, p.122869. https://doi.org/10.1016/j.conbuildmat.2021.122869.
27. Andrés Leonardo Neira Medina, Joaquín Abellán García, Nancy Torres Castellanos. (2022). Flexural behavior of environmentally friendly ultra-high-performance concrete with locally available low-cost synthetic fibers. European Journal of Environmental and Civil Engineering, 26(13), p.6281. https://doi.org/10.1080/19648189.2021.1938686.
28. Joaquin Abellan-Garcia, Jaime Fernández, M. Iqbal Khan, Yassir M. Abbas, Julian Carrillo. (2023). Uniaxial tensile ductility behavior of ultrahigh-performance concrete based on the mixture design – Partial dependence approach. Cement and Concrete Composites, 140, p.105060. https://doi.org/10.1016/j.cemconcomp.2023.105060.
29. Joaquin Abellan-Garcia, M. Iqbal Khan, Yassir M. Abbas, Andrea Castro-Cabeza, Julian Carrillo. (2023). Multi-criterion optimization of Low-Cost, Self-compacted and Eco-Friendly Micro-calcium-carbonate- and Waste-glass-flour-based Ultrahigh-Performance concrete. Construction and Building Materials, 371, p.130793. https://doi.org/10.1016/j.conbuildmat.2023.130793.
30. Guangshao Yang, Hejun Li, Qihao Ran, Rengui Xiao, Zhiyang Wang, Xiang Ke, Rui Yu, Xin Zou, Rui Yang, Li Yang. (2025). Mechanical performances and microstructures of ultra-high performance concrete incorporating spent fluid cracking catalyst under various curing regime: A comparative study. Case Studies in Construction Materials, 22, p.e04751. https://doi.org/10.1016/j.cscm.2025.e04751.
31. Joaquín Abellán García, Jaime Fernández Gómez, Nancy Torres Castellanos. (2022). Properties prediction of environmentally friendly ultra-high-performance concrete using artificial neural networks. European Journal of Environmental and Civil Engineering, 26(6), p.2319. https://doi.org/10.1080/19648189.2020.1762749.
32. Joaquín Abellán-García. (2021). K-fold Validation Neural Network Approach for Predicting the One-Day Compressive Strength of UHPC. Advances in Civil Engineering Materials, 10(1), p.223. https://doi.org/10.1520/ACEM20200055.
33. Joaquin Abellan-Garcia, Marielena Molinares, Nemesio Daza, Yassir M. Abbas, M. Iqbal Khan. (2023). Formulation of inexpensive and green reactive powder concrete by using milled-waste-glass and micro calcium-carbonate – A multi-criteria optimization approach. Construction and Building Materials, 409, p.134167. https://doi.org/10.1016/j.conbuildmat.2023.134167.
34. Carlos H. Mosquera, Melissa P. Acosta, William A. Rodríguez, Diego A. Mejía‐España, Jonhatan R. Torres, Daniela M. Martinez, Joaquín Abellán‐García. (2025). ANN‐based analysis of the effect of SCM on recycled aggregate concrete. Structural Concrete, 26(2), p.1435. https://doi.org/10.1002/suco.202400024.
35. Joaquin Abellan-Garcia, Daniela M. Martinez, M. Iqbal Khan, Yassir M. Abbas, Francisco Pellicer-Martínez. (2023). Environmentally friendly use of rice husk ash and recycled glass waste to produce ultra-high-performance concrete. Journal of Materials Research and Technology, 25, p.1869. https://doi.org/10.1016/j.jmrt.2023.06.041.
36. Rakesh Kumar, Baboo Rai, Pijush Samui. (2025). Prediction of mechanical properties of high‐performance concrete and ultrahigh‐performance concrete using soft computing techniques: A critical review. Structural Concrete, 26(2), p.1309. https://doi.org/10.1002/suco.202400188.
37. Joaquín Abellán-García, Juan S. Carvajal-Muñoz, César Ramírez-Munévar. (2024). Application of ultra-high-performance concrete as bridge pavement overlays: Literature review and case studies. Construction and Building Materials, 410, p.134221. https://doi.org/10.1016/j.conbuildmat.2023.134221.
38. Jesús E. Altamiranda-Ramos, Luis Castillo-Suárez, Jesús Redondo-Mosquera, Joaquín Abellán-García. (2025). Optimization of Sustainable Reactive Powder Concrete Incorporating Electric Arc Furnace Slag and Calcium Carbonate Powder via Central Composite Design. Construction Materials, 5(4), p.86. https://doi.org/10.3390/constrmater5040086.
Dimensions
PlumX
Visitas a la página del resumen del artículo
Descargas
Licencia
Derechos de autor 2019 DYNA
Esta obra está bajo una licencia internacional Creative Commons Atribución-NoComercial-SinDerivadas 4.0.
El autor o autores de un artículo aceptado para publicación en cualquiera de las revistas editadas por la facultad de Minas cederán la totalidad de los derechos patrimoniales a la Universidad Nacional de Colombia de manera gratuita, dentro de los cuáles se incluyen: el derecho a editar, publicar, reproducir y distribuir tanto en medios impresos como digitales, además de incluir en artículo en índices internacionales y/o bases de datos, de igual manera, se faculta a la editorial para utilizar las imágenes, tablas y/o cualquier material gráfico presentado en el artículo para el diseño de carátulas o posters de la misma revista.
